AccuGuide - 60 Hz
The AccuGuide® interconnect assembly maximizes performance by transmitting transients generated by lighting and switching with minimal voltage drops. Each AccuGuide unit includes our patented coaxial cables with minimize inductance. All systems also produce extremely low impedance, unattainable in conventional interconnect. As a result, the assembly delivers practically the entire surge to the Surge Protection Devise (SPD), clamping voltage are greatly reduced, and system performance is improved.
|  |
HSDS Series - 60 Hz
Developed specifically for data/telephone line protection, HSDS modules are Silicon Avalanche Hybrid Protectors for low voltage data and telecommunications applications, on pairs without the presence of ringing voltage. HSDS modules are designed for data and control applications as an isolated loop circuit protector(UL 497B).
|  |
Coaxial Protection - 60 Hz
Liebert model CF-200 and CF-200N are coaxial surge suppression devices designed for specialty applications such as repeater/duplexer antennas and other radio type communications.
The CF-200(UHF connectors) offers low loss even at frequencies approaching 500 Mhz. This is important for error-free data communication applications. The protector also features a replaceable cartridge.
|  |
Flow Meter Protection - 60 Hz
The Liebert FLW4 and FLW5 Series suppressors are designed for the water and waste
water industry. These multistage hybrid suppressors address over voltage transients
with gas tube and silicon avalanche technology. In addition, sneak and fault currents
are mitigated with new Positive Temperature Coefficient Thermistors (PTC's)
which consist of solid state resettable fuses. The units are encapsulated in stainless
steel pipe nipples making them suitable for use in severe environments. The FLW4
models protect a signal pair and the FLW5 models protect a signal pair plus the
cable shield (drain wire).
|  |
SND Series - 60 Hz
The SND Series surge protectors are designed specifically for medium exposure applications. Thus, the protectors can be used on pairs inside a building or leaving the building in conduit up to 500 feet. The SND Series offers several distinct advantages over other current technologies. Among the advantages are low cost, no series resistance, very durable, and completely solid-state.
|  |
LTS 1 Series - 60 Hz
The LTS-1 and LTS-2 Series is a multi-stage single or two pair surge suppressor designed for high exposure applications. These products were specifically designed to meet multiple low voltage protection applications in the fire and security industry.
|  |
LRA 5 Pin Module - 60 Hz
The LRA Series is an advanced, solid-state primary telecommunications five pin protection module. The module fits any industry standard five pin building entrance protector housing. All models employ state-of-the-art silicon breakover technology as the active over voltage clamping elements, along with fused over current circuitry which allows normal telephone current to pass, but quickly blocks damaging fault currents. The LRA Series modules must be grounded in an appropriate housing to Building Approved ground for proper operation.
|  |
LBT42 Series - 60 Hz
The LBT42 Series surge suppressor is a dual pair (four wire) module implementing
three stage hybrid technology. This module addresses over voltage transients with
gas tubes and silicon avalanche components. In addition, sneak and fault currents
are mitigated with resettable fuses "Positive Temperature Coefficient Thermistors"
(PTC's). The PTC's increase resistance several orders of magnitude when
overcurrents are removed. The ability to self restore in this manner significantly
increases suppressor performance and survivability.
|  |
Tel-200 Series - 60 Hz
TEL-200 Series modules are fused solid state secondary protectors of Key/PABX C.O.
(Central Office) trunk pairs. The units are available in two different circuit configurations.
The TEL-200 is constructed with solid state silicon avalanche foldback technology
and fuses. The TEL-200T features solid state silicon avalanche foldback technology
and Positive Temperature Coefficient Thermistors - PTC's. These protection
modules are intended to be used in conjunction with proper primary protectors (UL
497).
|  |
SBG Groundrail - 60 Hz
SBG Ground Rail - Fits Standard 66M1-50 Punch Down Blocks Liebert SBG Ground Rail
- Designed to fit standard 66M1-50 Punch Down Blocks. Allows Liebert's TEl,
EXT, SND, HSDS Series and other similar Surge Suppressors to access ground when
snapped onto the 66M1-50 Punch Down Block.
|  |
LTAC Series - 60 Hz
The LTAC Series suppressor was specifically designed to protect electronic instruments used by the water industry. It combines hybrid AC power protection and signal line protection in a NEMA 4X polycarbonate case. The AC power suppressor can supply up to 600 watts (total) on two separate output connectors and has a 10 amp replaceable fuse to prevent overloading the protective elements. An "INST PWR" LED provides visual indication that power is applied to instruments. Signal line protection is accomplished by the PC642 Series available in a variety of voltage clamps. Signal current can be monitored by reading the voltage across the 10Ohm, 1 % resistors (TP1 & TP2 @ or TP3 & TP4). All leads going to the LTAC board are terminated by quick disconnect or barrier block connectors to facilitate easy removal for service or replacement.
|  |
LBT64 Series - 60 Hz
The LBT64 Series surge suppressor is a single pair cube implementing three stage
hybrid technology. This cube addresses over voltage transients with gas tubes and
silicon avalanche components. In addition, sneak and fault currents are mitigated
with resettable fuses "Positive Temperature Coefficient Thermistors" (PTC's).
The PTC's increase resistance several orders of magnitude when overcurrents
exceed safe levels. A normal state resumed when overcurrents are removed. The ability
to self restore this manner significantly increases suppressor performance and survivability.
|  |
LBT52 Series - 60 Hz
The LBT52 Series is design to protect two pairs of wires specifically for alarm
and security systems where operating currents can be as high as 2.5 amps. Electrically,
the LBT52 Series is a rugged series hybrid implementing a staged complement of MOV's
and copper wound inductors. This design reduces series resistance to 0.2 Ohms per
pair. These products are intended to mate with the 12 pin industrial socket SPOS-12.
The LBT52 Modules plug into a base assembly (SPOS-12). The base assembly can be
mounted to any flat surface, and should be located as close as practical to the
protected equipment. Terminal 2 and / or Terminal 5 should be connections to Building
Approved ground with 12 gauge solid wire.
|  |
LBT-232 Series - 60 Hz
The LBT-232, utilizing silicon avalanche clamp devices, is a state-of-the-art surge protector for IEEE Std. RS-232C peripheral devices. The LBT-232 simply plugs in series with the data cable at or very near the equipment to be protected. If very long cable runs, or outdoor runs are present, the addition hybrid protectors at the building entry of the cable are recommended (see LBT42 Series).
|  |
LBLAN-24 Series - 60 Hz
LBLAN-24 with C5RT protection modules exceeds Category 5 EIA/TIA 568A signal transmission values for connectors.
Next: Exceeds -40 db on any pair combination.
Attenuation: Less than - 0.4 db per pair.
LBLAN-24 is a high density assembly designed to house up to six Liebert LAN Protection Modules. The modules can protect up to four pairs each and simply plug on the LBLAN-24 assembly. The protection modules are sold separately form the LBLAN-24 assembly.
LBLAN-24 utilizes the TYPE 110 (AT&T) connection system, and is capable of terminating solid or stranded 20-26 AWG wire. Wiring is one-to-one vertically down the assembly, input to output. The LBLAN-24 is configured to accept 6 sets of Category 5, four pair wiring.
|  |
CL Series - 60 Hz
The CL Series Surge Suppressor is a single Coax Line Protector implementing three stage hybrid technology. This Protector addresses over voltage transients with gas tubes and silicon avalanche devices. In addition, sneak and fault currents are mitigates with new Positive Temperature Coefficient Thermistors (PTC's), solid state resettable fuses. The CL Series is designed specifically for CCTV, DATA and AUDIO applications, offering two connector types BNC & F.
|  |